CUBIC
【CUBIC4&6】
“Swarf to Swarf” time is only 4.5 seconds.
Cubic is cutting edge hole processing machine which is equipped standard with 4 multi-spindle heads and “Swarf to Swarf” time is only 4.5 seconds. The incredible machining capability of Cubic ensures significant shorter cycle times than conventional multi-spindle & multi-head equipment. By adopting gear train system, a smooth transmission of rotation for each spindle is provided and rotation speed can be also set. The flexibility of multi-spindle head allows for easy changeover and setup to accommodate multiple workpiece models.
■SPECIFICATIONS
| Model | Cubic 4&6 | SpeedMagic |
| Control system | FANUC35i-MB |
|
| Axis control | 1 axis control |
|
| Max stroke | 500 mm |
|
| Workpiece size | Within head size |
|
| Spindle motor | FANUC αi 15/7000 | FANUC αi40/7000 |
| Spindle speed | Max 2,000 rpm | Max 12,000 rpm |
| Head to Head | 2.0 sec | 1.0 sec |
| Chip to Chip | 4.5 sec | 3.0 sec |
| Feed motor | αiF30/3000 | αis40/4000 |
| Index drive system | αiF22/3000 | αis30/4000 |
| Number of multi- spindle heads | 4sets/6sets |
|
| Size of each multi- spindle head | 400mm×500mm |
|
| Hydraulic tank unit | 40L | 60L |
| Multi spindle head clamp system | Mechanical |
|
| Weight | 8,000kg | 11,000kg |
■SPECIAL SPECIFICATION
| Head size | 450mm×550mm/500mm×600mm |
| Tool breakage detector | |
| Coolant tank with chip conveyor | |
| Jigs & Fixtures | |
| Index table / Shift unit | |
| Jig hydraulic tank unit |
・Specifications are subject to change without prior notice.
・The maximum size is listed for each motor above. It may differ depending on specifications.
TURREX
【TURREX MHC-4H】
TURREX MHC-4H is equipped standard with 4 multi-spindle heads and has the option(Head magazine&Head stocker) to equip more heads. During machining, 4 heads are indexed by AHC, and only one head is powered by a power unit and moving back and forth, therefore, few load is applied to feed unit, even if each head is weighting in over 300kg with tooling. Additionally, power unit is positioned by two positioning pins, therefore, machining precision is not affected by index precision.
■SPECIFICATION
| Model | MHC-4H |
| Control system | FANUC35i-MB |
| Axis control | 1 axis control |
| Maximum travel of spindle | 550 mm |
| Table width of spindle unit | 450 mm(slide bearing) |
| AC spindle motor | 11 kw |
| Spindle speed | Max.2,000 rpm |
| Feed motor (absolute) | AC.3.8 kw(Modela22) |
| Index drive system | FANUC α22 |
| Number of multi-spindle heads | 4sets/More |
| Size of each multi-spindle head | 450×600mm |
| Hydraulic tank unit | 40 L |
| Weight | 9,000 kg |
| Multi spindle head clamp system | Hydraulic |
■NC Option
| Head size | 500mm×600mm/550mm×600mm |
| Tool breakage detector | |
| Coolant tank with chip conveyor | |
| Jigs & Fixtures | |
| Index table / Shift unit | |
| Jig hydraulic tank unit |
Specifications are subject to change without prior notice.
OPTION
【AUTO HEAD CHANGER】
AHC(Automatic Head Changer) allows TURREX to be equipped with over 7 heads and each head has easy changeover feature. 4 heads can be controlled in forward & reverse rotation through its drive system. By installing a head magazine at the back of the machine 9 heads can be equipped and it provides TURREX flexibility to accommodate a variety of work pieces. TURREX also has the option to install a head stocker to add more heads according to machining requirements.
【AUTO FIXTURE CHANGER】
Automatic fixture changer can be installed beside the machine to provide more flexibility to accommodate a variety of work pieces and a shuttle system allows workpiece loading and unloading during machining.
